• FAQ Category :
  • Maintenance program---Build board failed to rise to the top of Z axis
    Maintenance program---Build board failed to rise to the top of Z axisPreparation: tool box The first step: Unfix the two screws which show on the below left picture to remove the middle cover. The second step: You can adjust the impact position of limit
    Learn More
  • Maintenance program - replace limit switch board of XY
    Maintenance program - replace limit switch board of XY Preparation: tool box, cross screwdriverThe first step: Remove the motor wire of X axis , unfix the screw on the limit switch board as the red arrow in the following picture shows. The second step: If
    Learn More
  • Maintenance program - replace motherboard
    Maintenance program - replace motherboardPreparation: tool box, cross screwdriver, multimeter(may be used) soldering iron(may be used)The maintenance program is relatively difficult than others, if you have other solutions then the prior choice is to do o
    Learn More
  • Maintenance program - replace hot bed
    Maintenance program - replace hot bedPreparation: Tool boxThe first step: Adjust the adjustment knob counterclockwise one by one until screw out them.The second step: Remove the hot bed and unplug the wiring harness below the bed. Specific shows below:The
    Learn More
  • Maintenance Program - replacement of nozzle / PTFE / heating tube / thermocouple
    It is the most common maintenance process and usually need to prepare more tools than other processes(some tools are required to be prepared by yourself), including 2 pieces of wrench , a piece of straight screwdriver,3 pieces of allen wrench ( you can fi
    Learn More
  • Maintenance program - replace screen and its components
    Preparation: tool box, cross screwdriver, pliers(may be used)The first step: Take the allen wrench (which is packaged in the tool box) to unfix the two screws on the right side of the cover (the red arrows point their positions).The second step: Make sure
    Learn More
  • Maintenance program - Replace fuse
    Preparation: Tool box, word screwdriver or bladeThe following maintenance programs only be activated when the fuse is broken or the fuse needs to be adjusted according to the local voltage. Usually, the installed fuse is suitable and does not need to be c
    Learn More
  • FPC lines burn out
    The printer uses FPC cables to connect extruder and XY limit switch to the motherboard by connecting them to the pinboard firstly and then connecting to motherboard by normal wires. Compared with ordinary cable,FPC is thinner and more fragile, which will
    Learn More
  • Lights with is not working or color is abnormal
    When the machine is applied power, the color of lights is bright white, when the machine is heating up, the color of lights is red, when the machine finishes printing, the color of lights is bright white or red. ( It is usually that slicing by Cura, the c
    Learn More
  • Filament winding around spool holder
    Before leaving the factory, EcubMaker has already put spool holders, guiding tubes (white tubes) and filament supports (metal supports) in the package. The correct installation method is as follows:For EcubMaker filament, the best installation way is the
    Learn More
  • Extruder fan does not rotate
    Extruder fan does not rotateUnder normal circumstances, the extruder fans begin to work only when preheating temperature of extruder reaches 70 ℃ or above. That is to say, if the the temperature that thermocouple detected is below 70 ℃, the fans does not…
    Learn More
  • No filament extruded or the extruded filament is very sparse
    No filament extruded or the extruded filament is very sparseThe content of this chapter is very similar to printing offset, mainly discusses the mechanical and electrical problems of motor. It is brief introduced here.> Preheat the extruder and feed t
    Learn More
  • Printing offset
    The offset refers the offset distance has already reached centimeter amount, but not the deviation of repeating position or the deviation of base quantity within the range of millimeter amount. Look at the above pictures, the left one is the normal offset
    Learn More
  • Extruder moves irregularly
    Extruder moves irregularlyThe irregular movement includes the termination, pause, moving to the area beyond the normal printing range in the printing process and other abnormal movement. Such problems are usually caused by the electromagnetic interference
    Learn More
  • Prints can not stick to the plate
    > The prior solution is to adjust slicing parameters. Such as rising the plate temperature (set PLA above 70 ℃, set ABS above 100 ℃ ), adding raft, adjusting the percentage of the first floor to 150~200%;> Enclose the printing cavity > Clean the…
    Learn More
  • The damage of plate
    Because the material of pyroceram plate is glass, it is easy to rupture during transportation, We have taken a lot of measures to prevent it from damaging and in almost situation, it is safe. However, if the pyroceram plate slightly cracks, it has no eff
    Learn More
  • Plate is uneven
    The supplier of pyroceram can controls its smoothness within 0.15mm from the manufacture process that equals to the thickness of one layer. In theory, the manufacture process can not absolutely make sure its flat. However, the degree of unevenness for alu
    Learn More
  • Nozzle is not in the same level
    Nozzle is not in the same level
    Learn More
  • Wear or tear of nozzle
    Wear or tear of nozzle
    Learn More
  • Jam of nozzle
    There are many reasons for jam, it needs to do specific analysis according to different situations and uses specific solutions. Refer to the picture of dual extruder kit, for different locations of the jam, it usually has following solutions:1. Nozzle
    Learn More
  • Failed to print
    Failed to print Choose the target file and click the print function, the normal processes is:①Heating up the board ②Heating up the extruder ③ Move the X,Y,Z axis to home position ④Extruder loads filament about 45mm in advance ⑤After that, extruder mov…
    Learn More
  • Failed to read the SD card
    Failed to read the SD card In the normal condition, when the printer powers on, inset the SD card , the OLED screen will refresh one time. In the printing menu, the gcode files will show in English while Other format files and languages can not display in
    Learn More
  • Abnormal Preheating
    Abnormal Preheating 1 The preheating target temperature of extruder shows abnormal date ( 0 ℃ or 1036 ℃ such as extreme temperature) Thermocouple is poor contact or broken. It needs to change a fine thermocouple to verify the two possibilities . Lear…
    Learn More
  • Unable to restart the printer
    Unable to restart the printer ( Neither printer’s lights nor display doesn’t work when powering on.) Change another place to get the electricity, making sure the power supply is in a proper condition. Change another power cord which is the …
    Learn More
  • 易立创Fantasy Pro底板调平教程(中文)
    Learn More
  • 易立创fantasy Pro打印机更换耗材教程(中文)
    Learn More
  • 易立创FANTASY pro系列开箱视频(中文)
    Learn More
  • EcubMaker FANTASY Pro series Unpacking Demo
    Learn More
  • printing process of Fantsay pro Series
    Learn More
  • FANTASY Pro plate leveling demo
    Learn More
  • 3d printer unpacking tutorial
    Learn More